Product Information
Categories: BURNERS, OVENPAK 2MAXON Connecting brackets and linkage assemblies are available in 4 main versions:
- Maxon SMARTLINK DS drive motors.
- Honeywell MODUTROL drive motors.
- Honeywell HERCULINE drive motors.
- Barber-Colemand drive motors.
Special assemblies can also be engineering upon request.
Related Products
GUIDE TUBE – OVENPAK 2
MAXON guide tubes allow for the simple installation of either UV flame detection cells of flame rods. Designed to penetrate through the entire burner to visualize the flame directly of the nozzle tip, the carbon steel guide tubes are available with either NPT or TEC end connections.
MAXON OBSERVATION GLASS – RECTANGULAR – OVENPAK 1
MAXON observation glass allows for proper viewing of flame quality through the back plate of the burner. Includes two (2) sealing o-rings and is available in standard plexiglass or high temperature Quartz models.
LINKAGE KIT – OVENPAK 2
MAXON linkage kits allow for the direct coupling of the internal air/gas butterfly valves of the Ovenpak 2 burner series.
The kit includes:
- Butterfly dics
- Linkage arms
- Pins
- Seals
- And bushings to allow fo the complete replacement of the control internals.
MIXING CONE – OVENPAK 2
"MAXON mixing cones are availble in 3 versions:
- Standard cast iron mixing cone, suitable for most process applications.
- Excess air cast iron mixing cone, allowing +/-10% more air through the burner with the same overall pressure drop.
- Stainless steel mixing cone, suitable for high temperature or highly corrosive applications.
MAXON MIXING CONE – OVENPAK 1
"MAXON mixing cones for the Ovenpak 1 are availble in 3 versions:
- Standard cast iron mixing cone, suitable for most process applications.
- Excess air cast iron mixing cone, allowing +/-10% more air through the burner with the same overall pressure drop.
- Stainless steel mixing cone, suitable for high temperature or highly corrosive applications.
BLOWER MOTOR – OVENPAK 1
MAXON blower motors are available in with the following voltages:
230/460/3/60
575/3/60
115/1/60
BURNER SLEEVE GASKET – MAXON OVENPAK 2
MAXON burner sleeve gasket is to be installed between the main burner flanges and the oven wall. Designed to provide an airtight seal around the burner flange under the most extreme conditions, the burner sleeve gasket must be installed on all applications with position combustion chamber pressures. The gasket is considered a consumable item and should be replaced during regularly scheduled burner maintenance.
GAS INLET GASKET – OVENPAK 2
MAXON gas inlet gasket is to be installed on the gas inlet flange of the burner casing. Designed to provide an gastight seal around the inlet flange of the burner casing, this gasket should provide a worry free seal under a variety of environmental conditions. The gasket is considered a consumable item and should be replaced during regularly scheduled burner maintenance.
FIRING SLEEVE – OVENPAK 1
MAXON firing sleeves are available in 5 versions:
- Standard sleeve is 8″ long, made of #310 SS, and is suitable for downstream temperatures up to 1000°F (538°C).
- For higher velocities, specify 12″ long sleeve made of #310 SS for downstream temperatures up to 1000°F (538°C).
- For higher downstream temperatures between 1000°F (538°C) and 1500°F (816°C), specify 8″ long, #RA 330 SS sleeve.
- For higher velocities and downstream temperatures between 1000°F (538°C) and 1500°F (816°C), specify 12″ long, #RA 330 SS sleeve.
- For refractory lined furnaces, specify 8"" refractory lined sleeve. "
SPARK IGNITOR – OVENPAK 2
MAXON spark ignitors have been engineered specially for industrial burner applications. Quality construction provides maximum service life and dependable operation to keep your heating process running smoothly. Consult technical bulletins to ensure your setup is per manufacturer`s recommendation for your specific OP2 model.